Products

Microwave Sensor LED LightBack

Motion Sensor

  • This product adopts microwave technology, to test ambient movement intelligently, auto-adjust work state, so no ambient temperature nor noise interruption, performance is better than the PIR sensor, sound-control switch and the touch switch.
  • Sensor should be placed parallel to the ground when installation, to make sure the most sensitivity.
  • Sensor against the metal block in front of it.
  • Sensor can get through glasses, wood board, plasterboard and other non-metallic object.
  • Sensor area tested from a person at the average height of 1.6~1.7m,walking speed for 1.0~1.5 m per second. If testing standard different, sensor area will be different.

Feature

  • High light efficiency over 120LM/W.
  • Scale-shaped Aluminum for good heat dissipation.
  • Low decay less than 3% after 10,000hrs’ working.
  • Constant current LED driver, more safe.
  • AC/DC available, also used to solar/wind power.
  • Work with DC constant current source or solar controller, Four-type intelligent light-adjusted:100%, 75%, 50%, 30%.
  • Saving up 90% more than traditional light.
  • Special circuit design, any individual LED failure will not cause other LEDs in working condition to black out.

Application

Road, Street, Garden, Park of Hotel, Hospital, School, villa.



Microwave sensor LED Bulb Light

Advantage

  • Lighting source's brightness controlled by microwave sensor, to avoid ambient temperature or noise interruption.
  • Specially designed for corridors and passageway, light on when people movement around, light off when silence, energy saving more than normal LED.
  • Special design, delaying time, sensor area can be adjustable by screwdriver ourself (Refer to debugging guide on page 5).
  • The lowest silence power can be 0.38W, energy saving better.
  • Internal sensor, no need install seperately, installation cost will be much lower.

Feature

  • Flake-type heat sink, stable in performance.
  • Without mercury or lead. Non-ultraviolet or flickering, no harm to health.
  • Internation standard E27 base, replace incandescent lamp and energy saving lamp directly.

Principle


  • Radar controlled, called Doppler effect. To test ambient movement intelligently, auto-adjust work state.
  • When people closer and closer(1-10meters, adjustable), auto-sensor receive signal and transmit to let light fully work at 100% (5W), its illumination equals to 40W incandescent lamp.
  • After people left, auto-sensor will automatically turn off (0%) for energy saving more.

Application

  • Widely used in corridors, passageway, washroom, balcony, basement and other places where need 24 hours lighting.

Parameter

Type ES-BL-06
Movement power 3W 5W 7W
Silence power (Unadjustable) 0.38W 0.38W 0.38W
LED qty (Epistar SMD5730) 6pcs 10pcs 14pcs
Lumens ≥170lm ≥300lm ≥420lm
Size Φ58mmxL125mm
Sensor area 1-10m (adjustable)
Sensor angle 140°
Lighting last 20S (adjustable)
React time 0.5S
Working voltage AC85-277V
Lighting angle 120 °
CRI >75Ra
Colors Temp. 3000-7500K(Warm White/Neutral White/Pure White/Cool White)
Lifespan ≥30000H
Material AL (good quality for heat dissipation) +PC
Working Temp. -20~+60°C



Microwave sensor T8 LED Tube

Advantage

  • New technology, sensor and smart IC are integrated inside tubes, no need additional ballast.
  • Special internal isolated power driver design, high watt available(25W), adjusted in delay time, sensor area, Min watt. 100% high voltage- resistance test, more safe.
  • No ambient temperature nor noise interruption like PIR or voice-controlled, sensor area at least 10m.
  • Special gridding circuit design, any individual LED failure will not cause other LEDs working.

Feature

  • Saving up 90% more than fluorescent tube, 60% more than normal LED T8 .
  • Meet the Europe standard of CE, RoHS, FCC certification.
  • No Hg, Pb or other hazardous materials, no radiation, environment friendly.
  • No frequency flash, instant startup, no hurting eyes.

Principle


  • Radar controlled, called Doppler effect. To test ambient movement intelligently, auto-adjust work state.
  • When driving a car closer and closer(5-10meters, adjustable), auto-sensor receive signal and transmit to let light fully work at 100% (25W), its illumination equals to 60W fluorescent.
  • After car parked and people left, auto-sensor will automatically turn down at 30%(adjustable) for energy saving.

Application

  • Widely used in basement, parking lots, warehouse, corridors, passageway, elevator, bus stop, villa and other places where need 24 hours lighting.

Parameter

Type ES-T8-06
Length 600mm 1200mm 1200mm 1500mm 1500mm 1800mm
Movement power 9W 18W 20W 20W 25W 25W
Silence power (adjustable) 2.5W 5W 6W 6W 7.5W 7.5W
LED qty (Epistar SMD2835) 60pcs 105pcs 105pcs 105pcs 150pcs 150pcs
Lumens >920lm >1820lm >1980lm >1980lm >2470lm >2470lm
Sensor area 5-10m (adjustable)
Sensor angle 140 degree
Lighting last 20s (adjustable)
React time 0.5s
Working voltage AC85-277V
Lighting angle 120 degree
CRI >75Ra
Colors Temp. 3000-7500K(Warm White/Neutral White/Pure White/Cool White)
Power factor >0.92
Lifespan ≥30000H
Material AL (good quality for heat dissipation) +PC
Working Temp. -20~+60°C



Microwave sensor LED Ceiling Lights

Advantage

  • With the new integration technologies, sensor and smart IC are integrated inside of LED ceiling light , easy to install.
  • Special internal isolated power driver design, High sensitivity to 10m, wide sensor area.
  • Full brightness when ambient movement, 20S after people left, it will light 30% brightness.
  • Sensor area, delay time, Min watt can be adjusted as customer's requirement before shipment.
  • No ambient temperature nor noise interruption like PIR or voice-controlled.

Feature

  • Without glass component, impact and vibration resistance, easy to transport.
  • No Hg, Pb or other hazardous materials, no radiation, environment friendly.
  • 100% high voltage- resistance test, more safe.
  • Meet the Europe standard of CE, RoHS, FCC certification.

Principle

  • Radar controlled, called Doppler effect. To test ambient movement intelligently, auto-adjust work state.
  • When people get close to stairwell (5-10meters, adjustable), auto-sensor receive signal and transmit to let light fully work at 100% (15W), its illumination equals to 38W energy saving lamp.
  • 20s after people left, auto-sensor will automatically turn down at 30%(adjustable) for energy saving.

Application

  • Widely used in corridor, passageway, porch, stairwells, washing room, basement ect.

Parameter

Type ES-DL-04
Length Φ300mmxH100mm Φ350mmxH100mm
Movement power 12W 15W
Silence power (adjustable) 4.5W 5.5W
LED qty (Epistar SMD5730) 24pcs 30pcs
Lumens >800lm >1000lm
Sensor area 5-10m (adjustable)
Sensor angle 140°
Lighting last 20s (adjustable)
React time 0.5s
Working voltage AC85-277V
Lighting angle 120 °
CRI >75Ra
Colors Temp. 3000-7500K (Warm White/Neutral White/Pure White/Cool White)
Power factor >0.92
Lifespan ≥30000H
Material AL (good quality for heat dissipation) +PC
Working Temp. -20~+60°C

Copyright © www.ecosolenergy.com 2014-15 - All rights reserved.
TOP